Conclusive 5040 fix for all nVIDIA users !

[elior77]

Follow me and you will be OK

Note - make sure you update your matrox to firmware 2.3.40 and video table 6.56.
1. Install nvidia driver.
2. Install PowerDesk and run the wizard for 1680x1050x1 @ 60Hz
3. Create a custom resolution in nvidia driver with the same numbers you see in the pic:
4. PLAY AROUND WITH THE VERTICAL REFRESH RATE till you found the number that works for you. ex. 59.454 ,59.400 etc...
5.
- Go to your Powerdesk SE install folder.
- Edit DeviceInfo.ini with notepad, find and replace all
"Name=CUST_MODE" to "Name=CUST_MODE_1" and
"Name=CustomDisplay" to "Name=CustomDisplay_1"
- Reboot
6. Send me your love - and have a blast playing @ [email protected] :rockout

Big thanks to gshlomi for his help and testing !

[cemnahit]

By the way Horizantal polarity (+), Vertical polarity (-) is also working for me... And every monitor in the market can do 59HZ because it is not exactly 59, it calculates as 60HZ in the system.

and also 1440x900 x 3
To make this resolution work first i created single screen 1440x900 from matrox wizard.



I posted the solution already http://www.widescreengamingforum.com/fo ... 2&start=30 :cheers

and you can play with HZ also to match your system, and system will see this as 60Hz without any problems.

And thank you for posting custom resolution fix.

[elior77]

Your post does not say anything about playing around with the vert freq.

We had to figure it out our selves.

Your post did give as hope we can do it.

Great work :mrgreen:

Thank you for your input !

[cemnahit]

Thanks i am happy that the solution helped you and i think this post will help everyone with matrox to do 5040 and 4320 resolutions. I think this a Universal solution for every matrox user.

For best result and solution , first you can install 182.50(Vista 64 bit drivers) and make sure your displays work at 5040x1050, and then take screenshot of the values in your Nvidia Control panel custom resolution section and ofcourse try to reach the aproximate values in newest drivers.

[Aexrael]

It's working now, followed your writeup to the letter.

1) Clean install of Win 7 x64
2) Updated Firmware (from same version to same version, I believe this resets the GXM settings?)
3) Reboot
4) Installed Nvidia 195.81 BETA drivers
5) Reboot
6) Installed Matrox PowerDesk 2.06
7) Reboot
8) Ran through Wizard, set 1680x1050 via the Auto selection.
9) Reboot
10) Wizard runs through the remaining three checkpoints BUT the screens change and black out. OCD for the monitors shows it running at 12x something resolution.
11) Shutdown
12) Startup, resolution is 1680x1050.
13) Swap displays, so I could get output on center monitor.
14) Via Nvidia Control Panel configured custom resolution as per OP instructions, with a Vrefresh of 59.400
15) Edited ini file as per OP instructions.
16) Rebooted
17) Matrox prompt detected changes, click yes for reboot.
18) Reboot
19) Change desktop resolution via Windows to 5040x1050.
20) Subsequent reboots, all is well in wonderland.

Gonna go reinstall steam and what not again, and hopefully this will last.
Something I noticed while reading through the inifile was the lack of W7 entries, it was all XP and Vista.

[Beazil]

Hmmm... Nicely done! I haven't tried this yet because I did the evil of all evils thing.

I went back to xp. Solved all my issues at once. Maybe I'll try a dual boot or something.

[slip-stream]

Bravo. Bravo. Can't wait for mine to arrive now. Tomorrow fingers crossed. :rockout

[elior77]

It's working now, followed your writeup to the letter.

1) Clean install of Win 7 x64
2) Updated Firmware (from same version to same version, I believe this resets the GXM settings?)
3) Reboot
4) Installed Nvidia 195.81 BETA drivers
5) Reboot
6) Installed Matrox PowerDesk 2.06
7) Reboot
8) Ran through Wizard, set 1680x1050 via the Auto selection.
9) Reboot
10) Wizard runs through the remaining three checkpoints BUT the screens change and black out. OCD for the monitors shows it running at 12x something resolution.
11) Shutdown
12) Startup, resolution is 1680x1050.
13) Swap displays, so I could get output on center monitor.
14) Via Nvidia Control Panel configured custom resolution as per OP instructions, with a Vrefresh of 59.400
15) Edited ini file as per OP instructions.
16) Rebooted
17) Matrox prompt detected changes, click yes for reboot.
18) Reboot
19) Change desktop resolution via Windows to 5040x1050.
20) Subsequent reboots, all is well in wonderland.

Gonna go reinstall steam and what not again, and hopefully this will last.
Something I noticed while reading through the inifile was the lack of W7 entries, it was all XP and Vista.

Great input dude ! thanks !

Have fun :)

[inteljoc]

I f***ing love you dude !!!!! You're my f***ing hero !!!!!

I can't believe I am writing this at 5040 with aero in Win7 x64 with 195.81 driver ...

I was previously on 181.71 with beta Powerdesk.

Now everything runs OK on SLi GTX285 with one Acer AL2223W and two Samsungs 2243bwx.

Running good at first try on 5040x1050 @ 59.400 Hz.

[scavvenjahh]

Oh the enthusiasm... :roll:
Did the 'sticky swap', time to give this stuff a good try now I suppose...

[johnds]

THANK YOU!

I just got the TH2Go 2 days ago, and just today got my third monitor. I was unable to get 5040 x 1050 (from PowerDesk) to work until I tried this.

My only problem is that yesterday, I had successfully set up a dual 1980 x 1080 (x2), so that is my native resolution because I can't get the Powerdesk Wizard to get me through the 3 monitor setup without reporting the Windows error.

So none of my games list 5040 x 1050.

But, I'm not doing too bad compared to the battles some of you frontier fighters have had to put up with. Thanks to everyone for their efforts.

John

[elior77]

1980?

5040x1050=1680x1050x3... m I missing somthing ?

I didnt understand your post realy...

[Paddy the Wak]

Thank you ... elior77 ... :twothumb

I have only been able to get Triple-Wide in Win 7 64-bit with the 181.71 drivers and I've been so busy of late that I gave up on Triple-Wide ... I went back to 3 x 5:4 monitors.
So ...
I already had the latest firmware, Powerdesk and drivers installed but I was running 3 x 5:4 monitors.
I switched to my 3 x 16:10 screens and followed your directions from "run the wizard for 1680x1050x1 @ 60Hz" in point 3.
In the custom resolution settings I set the Vertical refresh rate at 59.400 and all worked fine ...
I now have 5040x1050 @ 59.400Hz working in Win 7 with 195.62 drivers ... :surroundsmiley

Here's some links to the latest firmware, Powerdesk and drivers for those looking for them ...
Firmware (2.3.40.t6.56) ... http://www.matrox.com/graphics/en/support/drivers/download/?id=360
Powerdesk (2.06.00.026) ... http://www.matrox.com/graphics/en/support/drivers/download/?id=354
Drivers (GeForce 195.62 Win 64-bit) ... http://www.nvidia.co.uk/object/win7_winvista_64bit_195.62_whql_uk.html

Love sent ... :triplewide

Edit: typo.

[JohnnyG]

Newbie to this forum. Please correct me if I'm wrong.

Most of the people here that run an i5 or an i7 are the ones having problems?

I, myself run a E8400 with Win7 and everything runs correctly with TH2G. The reason why I bring this up is because I was thinking of moving up to a i7. I believe I'm missing something that you guys know that I don't know that you guys know about. :hide

[elior77]

***Nothing to do with i5 or i7 systems***


go go go !

59.4Hz seems to work for you guyz, we got something going here !

Very happy to get all that love :)

[Aexrael]

Newbie to this forum. Please correct me if I'm wrong.

Most of the people here that run an i5 or an i7 are the ones having problems?

I, myself run a E8400 with Win7 and everything runs correctly with TH2G. The reason why I bring this up is because I was thinking of moving up to a i7. I believe I'm missing something that you guys know that I don't know that you guys know about. :hide

Only thing wrong is the PowerDesk software and it's inability to setup the correct custom resolution for the respective monitors and GPUs people have. As Elior77 said, nothing to do with I6 or I7 systems.

[Tommy Trauma]

So has anyone tried this with Vista 64 yet?

[Aexrael]

You have fairly similar hardware to me, but I haven't tried Vista, but to be honest I don't see why it would be different between V and 7.

[rostato]

All works for me untill I reboot, and martox says something like, your settign have changed please reboot...

I reboot, and I am back to 3840x1050

How many cust_modes , and customdisplay's are there? I found like 4 or 5

All you have to do is add _1 to all of them? Seems a little to good to be true...

[elior77]

true true it's true :)

do it and have fun !