Widescreen Gaming Forum

The Destroyer has a "2 over 3" setup, which would be similar to what you have in #3. His setup had 3x 16:9 on the bottom row. He's running that now.

The WSGF v2 will fit set #1 and #2 out of the box. I did both of those with my LG 34" ultrawide and 2x Dell U2515H. You can see pics here - http://www.wsgf.org/article/review-lg-3 ... lay-page-2

You can do #3 with the WSGF v2, plus this upgrade kit. I've only got one left in stock, and not sure I'm going to restock once it's sold. I thought it would be a popular configuration, but that hasn't turned out to be the case. - http://www.wsgf.org/products/upgrade-kit-2x-bar

Sorry for not responding sooner. Didn't see the question in your post. I have 3x Dell U2515H, and I currently have 30 degrees on them, with more than six inches left on the bar to push them out further. I did a quick test, and I've got enough room to get a full 90 degree right angle between them, with room still to spare on the bar.

In case you were curious.

WSGF v2 looks perfect, and the upgrade kit opens the possibility of adding another cheeky pair of 24"s but I'm the UK and shipping would almost double the price :/ Any idea whether the Ergotech Triple Monitor Stand w/Telescoping wings would also fit a 3x1 setup?

Alternatively, do you ship to US PO boxes or have any UK / EU distribution points to cut the cost on shipping?

TheDestroyer wrote:In case you were curious.

That looks amazing. Probably not a good idea for the wallet...

didYouSayGravitas wrote:

TheDestroyer wrote:In case you were curious.

That looks amazing. Probably not a good idea for the wallet...

The upgrade kit for the "2+" is only $80.

Thanks. Went ahead to make an order. Looking forward to it.

We are all caught up on backorders now.

didYouSayGravitas wrote:WSGF v2 looks perfect, and the upgrade kit opens the possibility of adding another cheeky pair of 24"s but I'm the UK and shipping would almost double the price :/ Any idea whether the Ergotech Triple Monitor Stand w/Telescoping wings would also fit a 3x1 setup?

Alternatively, do you ship to US PO boxes or have any UK / EU distribution points to cut the cost on shipping?

I can ship to US PO Box if needed. I don't have any UK/EU distribution points. Sorry.

I just got my stand in Yesterday and got it all setup. I'm using 3 ASUS VG278HE 27" and a Dell U2410 24inch in 3x1. I have a slight problem though. The Left monitor is nice and flush with the center however the right monitor is 1/2 inch lower than the center. I have adjusted the knob adjustment to the highest setting and its still 1/2 inch to low. There is noticeable drop on the support arm on the right side that the left does not have. Any advice would be greatly appreciated. Thanks in advance

v/r
Kaash

Kaash wrote:I just got my stand in Yesterday and got it all setup. I'm using 3 ASUS VG278HE 27" and a Dell U2410 24inch in 3x1. I have a slight problem though. The Left monitor is nice and flush with the center however the right monitor is 1/2 inch lower than the center. I have adjusted the knob adjustment to the highest setting and its still 1/2 inch to low. There is noticeable drop on the support arm on the right side that the left does not have. Any advice would be greatly appreciated. Thanks in advance

v/r
Kaash

Kaash,

Sorry for this issue. Every so often a bar comes out that isn't perfect. It may be that the hinges/joints are not all properly tightened (rare), or that the pole clamp wasn't set perfectly flat, or that possible the holes drilled for the hinges were not done perfectly (most likely).

You can first try to take the monitors off and make sure all the bolts on the hinges are tightened. Another option would be for me to send you an adjustable pivot to use in the bottom middle. This should allow you to even everything out. Last option is for me to replace the bar for you.

In my shipment confirmation, I had provided my email so that you could contact me directly if there were issues. That's the easiest and quickest way to communicate. I will send you and email, and we can chat there.

Thanks,
Skip

i have 5 BenQ 2720Z monitors and was wondering if i could have a config like this with the 2+ upgrade for $80 ,will it handle 2-27"ers?

was just going to do 1+3 with the stand and set the extra 2720z off to the side but this config looks really interesting

TheDestroyer wrote:
In case you were curious.

This bar will only handle 2x 24". The bar was also a very slow seller, so I've pulled it out of the store.

You could potentially use a 5-segment bar upgrade kit and just use the middle three segments.

I'd have to measure to see if that would work.


Sent from my iPhone using Tapatalk

Soo happy with my setup! Was a breeze to install

oghabib wrote:Soo happy with my setup! Was a breeze to install

Edit: Sorry! Images rotated themselves for some reason.

Man the base is huge!



Really easy to install. Can't make use of all three screens though due to my faulty GTX 980 Ti. My spare GTX 770 does not have 3 x DP, and I don't have a converter.



Setup is very clean now, with all the cables secured to the stand with the bundled cable management clips.



The only question that the instructions do not address.. What the heck is this thing for?

c1em3ntchua wrote:Man the base is huge!

Indeed. That's what keeps the unit so stable, and from tipping over while you're installing stand.

c1em3ntchua wrote:The only question that the instructions do not address.. What the heck is this thing for?

You can stick it on the back of the collar on the base, and stick in the allen wrench (hex key) used for the set screw.

skipclarke wrote:

c1em3ntchua wrote:Man the base is huge!

Indeed. That's what keeps the unit so stable, and from tipping over while you're installing stand.

c1em3ntchua wrote:The only question that the instructions do not address.. What the heck is this thing for?

You can stick it on the back of the collar on the base, and stick in the allen wrench (hex key) used for the set screw.

Ah a handy allen key holder. Thanks for the clarification.

Hi,may i ask you a "stupid" thing? If i order the stand from Europe (precisely Italy) i need to check EU shipping or do you suggest me another method? Just wanted to know if the shipping it's different in term of taxes (i wanted to choose EU anyway but i prefer to ask you this stupid question ). I have 3 asus pg278q as monitors,and i may add one more in a 1 over 3 config.

You would pick the EU shipping. The shipping fees only cover the actual shipping and handling fees I incur. You are still responsible for any extra import duties, fees or taxes.


Sent from my iPhone using Tapatalk