Widescreen Gaming Forum

Hello WSGF i was using a GTX 580 and was able to get 5040x1050 right out of the box until my card took a dump~
i was only able to replace with my current card which was supposed to also be a slight upgrade. However i am not able to meet my resolution needs with this card for some reason. Im also new to using AMD as i have had Nvidia products until now. Im looking for any help to get my resolution back to 5040x1050

Current Max resolution available to me is 3840x1024


Here is my setup
x3 Dell E228WFP 22"
Gigabyte 7950 3GB
Matrox Triplehead2go Digital
Matrox Powerdesk Version 1.11.0001.0511 2.07.01 GXM
AMD Radeon HD 7900 Series Driver Version 8.921.2.0



other specs if needed :
Catalyst Control Center Version 2012.0119.1236.22534
OS Name Microsoft Windows 7 Ultimate
Version 6.1.7601 Service Pack 1 Build 7601
Other OS Description Not Available
OS Manufacturer Microsoft Corporation
System Name VEGAS
System Manufacturer System manufacturer
System Model System Product Name
System Type x64-based PC
Processor Intel(R) Core(TM) i7-3820 CPU @ 3.60GHz, 3601 Mhz, 4 Core(s), 8 Logical Processor(s)
BIOS Version/Date American Megatrends Inc. 0604, 10/3/2011
SMBIOS Version 2.7
Windows Directory C:Windows
System Directory C:Windowssystem32
Boot Device DeviceHarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "6.1.7601.17514"
Installed Physical Memory (RAM) 32.0 GB
Total Physical Memory 32.0 GB
Available Physical Memory 29.1 GB
Total Virtual Memory 64.0 GB
Available Virtual Memory 60.8 GB
Page File Space 32.0 GB

Thanks for any help
Killabee

_________________

Have you completely removed the nvidia drivers, like so? Can you set your monitors to their native resolution when in single display or extended mode (using p+win)? What happens when you set your monitors to duplicate mode?

_________________
Philips BDM4065UC(3840x2160) Acer Z35(2560x1080@200hz); 980 Ti Hybrid @stock ; 6700K 4.6ghz (1.35v)/D15; 16GB 3200mhz; Asus Maximus Ranger VIII; AX860; 1TB 960 EVO; 750GB 840 EVO; Teufel Concept D 500; Sennheiser HD6XX; Windows 10 (latest build)

Why do you use a TripleHead2Go when you have a AMD Radeon HD7950 and could run Eyefinity native ?

_________________
We gonna send it to outa space!

I also ask why you haven't tried Eyefinity.

It may be a lost cause, but try this: Thread

EDIT: I also have a sneaking suspicion about why the above solution wont work. I believe the TH2go is not sending 5040x1050 as it's highest supported resolution through EDID. This is kinda required. On my 30" monitor, I can only choose a resolution as tall as or lower than 1600 pixels and a resolution as wide as or lower than 2560. I think in order for this to work, Matrox has to make a firmware that will allow transmission of EDID information.

_________________
System Core: | Intel Core i5-2500K + ASUS P8Z68-V + 16GB Corsair XMS3 DDR3 1333 MHz | Win7 x64 | MSI R7970 Lightning 3GB [1105/1400] |
Display: | 3 x Dell Ultrasharp 3007WFP-HC @ 7680x1600 | Dell u3011 |

eyefinity? .. honestly i didn't know what that was until you said something.
To answer your question as to why i would use my matrox box is because i already owned the box from prior setups why go with anything else when i already am good with my triplehead2go. // however thank you for shedding the light on eyefinity i will check it out in the future.

as to the first reply when i bought the new card i also bought an SSD hard drive so i did a complete fresh install of windows so there were no old drivers. ((Fyi if you haven't gone SSD i recommend it the read times are amazing))

Solution for me is to just use this card until i can exchange it for another GTX 580 3GB card. Reason i can get my resolution is this card will only push out a max of 3840x1024 with triplehead2go digital .. unless there is some kind of work around that matrox obviously does not support.

you can check the different cards with this compatibility wizard here
http://www.matrox.com/graphics/en/support/compatibility/gxm/
my card is not listed .. probably to new.

thx for the replyz

Killabee

_________________

eyefinity? .. honestly i didn't know what that was until you said something.
To answer your question as to why i would use my matrox box is because i already owned the box from prior setups why go with anything else when i already am good with my triplehead2go. // however thank you for shedding the light on eyefinity i will check it out in the future.

as to the first reply when i bought the new card i also bought an SSD hard drive so i did a complete fresh install of windows so there were no old drivers. ((Fyi if you haven't gone SSD i recommend it the read times are amazing))

Solution for me is to just use this card until i can exchange it for another GTX 580 3GB card. Reason i can get my resolution is this card will only push out a max of 3840x1024 with triplehead2go digital .. unless there is some kind of work around that matrox obviously does not support.

you can check the different cards with this compatibility wizard here
http://www.matrox.com/graphics/en/support/compatibility/gxm/
my card is not listed .. probably to new.

thx for the replyz

Killabee

Amigo, instead of swapping cards just get a DisplayPort or MiniDisplayport adapter. That is all you need to get Eyefinity working, rather than swapping out GPUs.

Sounds like an easy fix to my resolution problem but honestly this card performs worse than the card i had before.

_________________