| Widescreen Gaming Forum https://www.wsgf.org/phpBB3/ |
|
| 6950 Dirt3 Edition Eyefinity Problem https://www.wsgf.org/phpBB3/viewtopic.php?f=66&t=22822 |
Page 1 of 1 |
| Author: | TboneGreen [ 04 Oct 2011, 18:02 ] |
| Post subject: | 6950 Dirt3 Edition Eyefinity Problem |
Greetings, This is my first post in these forums... hopefully I can be helped! I just picked up two Sapphire Radeon HD 6950's 2gb. I am upgrading from a 5850. Problem: With my 5850 I ran a 3 monitor eyefinity setup using 3 samsung 2343bwx monitors and a sapphire active displayport to dual link dvi adapter. I threw my new cards into my rig last week and since then have been unable to get them working with all three monitors. This is exactly whats happening: -both DVI monitors can be seen once in windows, and used normally. -once in windows, the displayport monitor does not have a signal going to it. CCC recognizes the monitor but it always remains black. -The monitor shows up in CCC and it looks like it is recognized. When it is enabled, CCC think its working, but the monitor is not receiving a signal -while at the bios screen and loading into windows, the display port monitor displays the bios screen and the windows loading screen. -if i power down and put my 5850 in, i can configure my eyefinity group with no problems. Motherboard: Asus P6T Deluxe V2 CPU: Intel Core i7 920 RAM: 3 x 2gb sticks of DDR3 OCZ Reaper Video Card: Sapphire 6950 2gb Dirt 3 Edition (I have 2 but am just trying to get one going for now) PSU: OCZ Fatality 700W Monitor: Samsung 2343bwx (x3) 2 hooked up by DVI, the third hooked up via Sapphire Active Dual Link Displayport Adapter Hard drives: Intel SSD 80gb (OS), Seagate 1tb (Storage) Optical Drives: N/A Additional PCI cards: Razer Barracuda AC-1 Soundcard Number of fans present: 2 x 140mm, 1 x 120mm, 1 x 200mm (Storm Sniper Case) Operating System : Windows 7 64 bit Home Premium Video Card Drivers in Use ( and tried ): I have tried 11.9 11.8, and 11.5 all with the same results. right now i'm running 11.9 Apps/Games causing issues: Everything in Windows All major components check 100% after thorough testing: Yes - works perfect when i swap my 5850 back in. System clean of viruses / spyware etc: Yes Other things tried: -I've read about a workaround where you unplug and plug in the displayport connector, but there isn't any real details on it, and what i've tried hasn't worked. -I've tried all kinds of driver sweeps and driver updates to no avail. The worst part is, is that as soon as I put my 5850 back into the computer everything works great. -The monitor shows up in CCC and it looks like it is recognized. When it is enabled, CCC think its working, but the monitor does not receive a signal. -I have managed to get the displayport monitor working in windows by either setting the resolution on it to either 800x600 or 1280x1024. any ideas? i'm pulling my hair out here and am starting to regret picking these new cards up! thanks in advance! |
|
| Author: | AussieTimmeh [ 05 Oct 2011, 07:40 ] |
| Post subject: | TboneGreen |
Greetings, How I got this to work was to setup the Eyefinity group regardless of what the monitors looked like (ie the DP monitor in an incorrect resolution because the CCC wouldn't let me choose the monitors native resolution no matter what I tried), then unplug and plug the adapter back in with everything running, which then suddenly let the monitor use its full resolution, at which point I could finish setting up the group. I did have to unplug and plug it in twice and it worked on the second time. Not sure that will help you alot here though. I find the CCC / driver setup very challenging and often proves to be random attempts of trying things rather than a set sequence. Hopefully someone else may have had this exact problem before to help you more. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|